API RP 14F PDF

0 Comment

Find the most up-to-date version of API RP 14F at Engineering The American Petroleum Institute’s Recommended Practice for Design and Installation of Electrical Systems for Offshore Petroleum Facilities, API RP 14F, un . Nov 5, For facilities classified as Zone 0, Zone 1, or Zone 2, reference API 14FZ, Recommended Practice for Design and Installation of Electrical.

Author: Tulrajas Mikarisar
Country: Nepal
Language: English (Spanish)
Genre: Love
Published (Last): 16 April 2016
Pages: 268
PDF File Size: 9.74 Mb
ePub File Size: 17.89 Mb
ISBN: 664-2-55525-623-1
Downloads: 43007
Price: Free* [*Free Regsitration Required]
Uploader: Moogukazahn

Providing protection from fire, smoke, water and blast pressures. The practitioner should in apii cases seek full and proper guidance from the relevant legislation and codes aapi practice in addition to following company guidelines and procedures. Must provide adequately maintained breathers and drains to prevent accumulation of moisture This document provides guidelines and recommended practice for the satisfactory design of offshore structures against fire and blast loading.

Its only intrinsically safe when employed in a properly ai intrinsically safe circuit. About project SlidePlayer Terms of Service. If Associate Apparatus is placed in the classified area then it must have another ai of protection. Grounding of electrical equipment on fixed and floating offshore petroleum facilities in a positive manner is of particular importance because personnel standing on steel decks or in contact with steel framing present a low impedance apii to ground, effectively grounded For sizing equipment grounding conductors, refer to NEC Table.

30 CFR 250.114 – How must I install, maintain, and operate electrical equipment?

This recommended practice is intended to assist in development of a management program designed to promote safety and environmental protection during the performance of offshore oil and gas and sulphur operations. This recommended practice covers methods of installation for pressure-relief devices for equipment that has a maximum allowable working pressure MAWP of 15 psig 1.

Published by Nickolas Allan Jenkins Modified about 1 month ago. Mineral-insulated metal-sheathed cable as defined by NEC Article Applicable gas classification group s. Nonincendive equipment is normally limited to communication and instrumentation systems. Inch, size or larger conduit run entering an enclosure that contains splices, taps, aip terminals.

TOP 10 Related  BLANCA OLMEDO LUCILA GAMERO DE MEDINA PDF

API RP 14F: Recommended Practice for Design and Installation of

These advantages may include reduced initial capital expenditures, enhanced safety, or facilities that are more easily and more economically maintained. Must be installed in and explosion proof container unless the certificate states otherwise.

OK Forward looking statement. Medias this blog was made to help people to easily download or read PDF files. The classified areas are different and some protection concepts also differ. C — Sparking equipment in which the contacts are suitably protected other than by restricted breathing. This document recommends minimum requirements and guidelines for the design and installation of new piping systems on production platforms located offshore.

If you wish to download it, please recommend it to your apu in any social system. Type PLTC nonmetallic-sheathed, power-limited tray cable.

Metal-clad cable for gp locations as defined in UL MI cable: This recommended practice covers methods of installation for pressure-relief devices for equipment that has a maximum allowable working pressure MAWP of 15 psig 1. Why is it NOT acceptable?

API RP 14FZ PDF

This document recommends minimum requirements and guidelines for the design and installation of electrical systems on fixed and floating petroleum facilities located offshore when hazardous locations are classified as Zone 0, Zone 1, or Zone 2. Metal-clad cable as defined by NEC Article This document 14r minimum requirements and guidelines for the design apu installation of electrical systems on fixed and floating petroleum facilities located offshore.

Energy Limited nL Limit energy of sparks; wpi qpi temperature of a device replaced by Ex ic. Explosion proof equipment may not provide protection against the ingress of liquids or solids therefore, breathers and drains may be required. This document recommends minimum requirements and guidelines for the design and installation of electrical systems on fixed and floating petroleum facilities located offshore.

14c accomplished by fusion of metal to metal or sealed through glass to metal. This document recommends minimum requirements and guidelines for the design, installation, and maintenance of electrical systems on fixed and floating petroleum facilities located offshore.

This recommended practice is intended to assist in development of a management program designed to promote safety and environmental protection during the performance of offshore oil and gas and sulphur operations. The basic function of a FPS is to receive hydrocarbons from the wellhead, process the hydrocarbons, and store This document provides guidelines and recommended practice for the satisfactory design of offshore structures against fire and blast loading.

TOP 10 Related  AUMENTAR ESTATURA PARA IDIOTAS PDF

Regulators such as U. Disconnect switches in general purpose enclosures should not be used offshore in classified locations; this is a departure from the NEC.

This document recommends minimum requirements and guidelines for the design and installation of new piping systems on production platforms located offshore.

The procedures for installation of the instruments covered in this recommended practice are based on experience with and evaluation of many installations.

Strict rules must be followed, system calculated to ensure energy levels are within tolerances and diagrams must be followed closely as wells as the current RP, Codes and Standards. Zone 2- Not likely or normally confined in containers. This ensures that apu gas or vapor located above the arcing or sparking parts or the gas or vapor located exterior apu the enclosure cannot be ignited by the electrical arcing parts within the oil.

Markings on the equipment to ensure the correct location of installation are as follows; Zone Equipment.

Zone 1 Equipment must be certified as meeting the requirements of the area this could tp a number of different protection concepts not just Flame-Proof.

This equipment has additional security against the possibility of excessive temperature 14v the equipment is assembled very carefully to ensure that arcing or sparking from part to part or connection to connection will not occur.

As tested by the NFPA This document is intended to bring together in one place a brief description of basic desirable electrical practices for offshore electrical systems.